[Intel-wired-lan] [PATCH] igb: add parameter to ignore nvm checksum validation
Alexander Duyck
alexander.duyck at gmail.com
Fri May 17 15:16:34 UTC 2019
On Thu, May 16, 2019 at 6:48 PM Florian Fainelli <f.fainelli at gmail.com> wrote:
>
>
>
> On 5/16/2019 6:03 PM, Daniel Walker wrote:
> > On Thu, May 16, 2019 at 03:02:18PM -0700, Florian Fainelli wrote:
> >> On 5/16/19 12:55 PM, Nikunj Kela (nkela) wrote:
> >>>
> >>>
> >>> On 5/16/19, 12:35 PM, "Jeff Kirsher" <jeffrey.t.kirsher at intel.com> wrote:
> >>>
> >>> On Wed, 2019-05-08 at 23:14 +0000, Nikunj Kela wrote:
> >>> >> Some of the broken NICs don't have EEPROM programmed correctly. It
> >>> >> results
> >>> >> in probe to fail. This change adds a module parameter that can be
> >>> >> used to
> >>> >> ignore nvm checksum validation.
> >>> >>
> >>> >> Cc: xe-linux-external at cisco.com
> >>> >> Signed-off-by: Nikunj Kela <nkela at cisco.com>
> >>> >> ---
> >>> >> drivers/net/ethernet/intel/igb/igb_main.c | 28
> >>> >> ++++++++++++++++++++++------
> >>> >> 1 file changed, 22 insertions(+), 6 deletions(-)
> >>>
> >>> >NAK for two reasons. First, module parameters are not desirable
> >>> >because their individual to one driver and a global solution should be
> >>> >found so that all networking device drivers can use the solution. This
> >>> >will keep the interface to change/setup/modify networking drivers
> >>> >consistent for all drivers.
> >>>
> >>>
> >>> >Second and more importantly, if your NIC is broken, fix it. Do not try
> >>> >and create a software workaround so that you can continue to use a
> >>> >broken NIC. There are methods/tools available to properly reprogram
> >>> >the EEPROM on a NIC, which is the right solution for your issue.
> >>>
> >>> I am proposing this as a debug parameter. Obviously, we need to fix EEPROM but this helps us continuing the development while manufacturing fixes NIC.
> >>
> >> Then why even bother with sending this upstream?
> >
> > It seems rather drastic to disable the entire driver because the checksum
> > doesn't match. It really should be a warning, even a big warning, to let people
> > know something is wrong, but disabling the whole driver doesn't make sense.
>
> You could generate a random Ethernet MAC address if you don't have a
> valid one, a lot of drivers do that, and that's a fairly reasonable
> behavior. At some point in your product development someone will
> certainly verify that the provisioned MAC address matches the network
> interface's MAC address.
> --
> Florian
The thing is the EEPROM contains much more than just the MAC address.
There ends up being configuration for some of the PCIe interface in
the hardware as well as PHY configuration. If that is somehow mangled
we shouldn't be bringing up the part because there are one or more
pieces of the device configuration that are likely wrong.
The checksum is being used to make sure the EEPROM is valid, without
that we would need to go through and validate each individual section
of the EEPROM before enabling the the portions of the device related
to it. The concern is that this will become a slippery slope where we
eventually have to code all the configuration of the EEPROM into the
driver itself.
We need to make the checksum a hard stop. If the part is broken then
it needs to be addressed. Workarounds just end up being used and
forgotten, which makes it that much harder to support the product.
Better to mark the part as being broken, and get it fixed now, than to
have parts start shipping that require workarounds in order to
function.
- Alex
More information about the Intel-wired-lan
mailing list