[Intel-wired-lan] [PATCH v1 1/3] e1000e: Add handshake with the CSME to support s0ix
Sasha Neftin
sasha.neftin at intel.com
Thu Jun 24 08:18:27 UTC 2021
On the corporate system, the driver will ask from the CSME
(manageability engine) to perform device settings are required
to allow s0ix residency.
This patch provides initial support.
Reviewed-by: Dima Ruinskiy <dima.ruinskiy at intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin at intel.com>
---
drivers/net/ethernet/intel/e1000e/ich8lan.h | 2 +
drivers/net/ethernet/intel/e1000e/netdev.c | 328 +++++++++++---------
2 files changed, 176 insertions(+), 154 deletions(-)
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.h b/drivers/net/ethernet/intel/e1000e/ich8lan.h
index 1502895eb45d..e59456d867db 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.h
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.h
@@ -47,6 +47,8 @@
#define E1000_SHRAH_PCH_LPT(_i) (0x0540C + ((_i) * 8))
#define E1000_H2ME 0x05B50 /* Host to ME */
+#define E1000_H2ME_START_DPG 0x00000001 /* indicate the ME of DPG */
+#define E1000_H2ME_EXIT_DPG 0x00000002 /* indicate the ME exit DPG */
#define E1000_H2ME_ULP 0x00000800 /* ULP Indication Bit */
#define E1000_H2ME_ENFORCE_SETTINGS 0x00001000 /* Enforce Settings */
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 646bfb83a18b..786719890f2b 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -6345,42 +6345,104 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
u32 mac_data;
u16 phy_data;
- /* Disable the periodic inband message,
- * don't request PCIe clock in K1 page770_17[10:9] = 10b
- */
- e1e_rphy(hw, HV_PM_CTRL, &phy_data);
- phy_data &= ~HV_PM_CTRL_K1_CLK_REQ;
- phy_data |= BIT(10);
- e1e_wphy(hw, HV_PM_CTRL, phy_data);
+ if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) {
+ /* Request ME configure the device for s0ix */
+ mac_data = er32(H2ME);
+ mac_data |= E1000_H2ME_START_DPG;
+ mac_data &= ~E1000_H2ME_EXIT_DPG;
+ ew32(H2ME, mac_data);
+ } else {
+ /* Request driver configure the device to s0ix */
+ /* Disable the periodic inband message,
+ * don't request PCIe clock in K1 page770_17[10:9] = 10b
+ */
+ e1e_rphy(hw, HV_PM_CTRL, &phy_data);
+ phy_data &= ~HV_PM_CTRL_K1_CLK_REQ;
+ phy_data |= BIT(10);
+ e1e_wphy(hw, HV_PM_CTRL, phy_data);
- /* Make sure we don't exit K1 every time a new packet arrives
- * 772_29[5] = 1 CS_Mode_Stay_In_K1
- */
- e1e_rphy(hw, I217_CGFREG, &phy_data);
- phy_data |= BIT(5);
- e1e_wphy(hw, I217_CGFREG, phy_data);
+ /* Make sure we don't exit K1 every time a new packet arrives
+ * 772_29[5] = 1 CS_Mode_Stay_In_K1
+ */
+ e1e_rphy(hw, I217_CGFREG, &phy_data);
+ phy_data |= BIT(5);
+ e1e_wphy(hw, I217_CGFREG, phy_data);
- /* Change the MAC/PHY interface to SMBus
- * Force the SMBus in PHY page769_23[0] = 1
- * Force the SMBus in MAC CTRL_EXT[11] = 1
- */
- e1e_rphy(hw, CV_SMB_CTRL, &phy_data);
- phy_data |= CV_SMB_CTRL_FORCE_SMBUS;
- e1e_wphy(hw, CV_SMB_CTRL, phy_data);
- mac_data = er32(CTRL_EXT);
- mac_data |= E1000_CTRL_EXT_FORCE_SMBUS;
- ew32(CTRL_EXT, mac_data);
+ /* Change the MAC/PHY interface to SMBus
+ * Force the SMBus in PHY page769_23[0] = 1
+ * Force the SMBus in MAC CTRL_EXT[11] = 1
+ */
+ e1e_rphy(hw, CV_SMB_CTRL, &phy_data);
+ phy_data |= CV_SMB_CTRL_FORCE_SMBUS;
+ e1e_wphy(hw, CV_SMB_CTRL, phy_data);
+ mac_data = er32(CTRL_EXT);
+ mac_data |= E1000_CTRL_EXT_FORCE_SMBUS;
+ ew32(CTRL_EXT, mac_data);
+
+ /* DFT control: PHY bit: page769_20[0] = 1
+ * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1
+ */
+ e1e_rphy(hw, I82579_DFT_CTRL, &phy_data);
+ phy_data |= BIT(0);
+ e1e_wphy(hw, I82579_DFT_CTRL, phy_data);
+
+ mac_data = er32(EXTCNF_CTRL);
+ mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG;
+ ew32(EXTCNF_CTRL, mac_data);
+
+ /* Enable the Dynamic Power Gating in the MAC */
+ mac_data = er32(FEXTNVM7);
+ mac_data |= BIT(22);
+ ew32(FEXTNVM7, mac_data);
+
+ /* Disable disconnected cable conditioning for Power Gating */
+ mac_data = er32(DPGFR);
+ mac_data |= BIT(2);
+ ew32(DPGFR, mac_data);
+
+ /* Don't wake from dynamic Power Gating with clock request */
+ mac_data = er32(FEXTNVM12);
+ mac_data |= BIT(12);
+ ew32(FEXTNVM12, mac_data);
+
+ /* Ungate PGCB clock */
+ mac_data = er32(FEXTNVM9);
+ mac_data &= ~BIT(28);
+ ew32(FEXTNVM9, mac_data);
+
+ /* Enable K1 off to enable mPHY Power Gating */
+ mac_data = er32(FEXTNVM6);
+ mac_data |= BIT(31);
+ ew32(FEXTNVM6, mac_data);
+
+ /* Enable mPHY power gating for any link and speed */
+ mac_data = er32(FEXTNVM8);
+ mac_data |= BIT(9);
+ ew32(FEXTNVM8, mac_data);
+
+ /* Enable the Dynamic Clock Gating in the DMA and MAC */
+ mac_data = er32(CTRL_EXT);
+ mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN;
+ ew32(CTRL_EXT, mac_data);
+
+ /* No MAC DPG gating SLP_S0 in modern standby
+ * Switch the logic of the lanphypc to use PMC counter
+ */
+ mac_data = er32(FEXTNVM5);
+ mac_data |= BIT(7);
+ ew32(FEXTNVM5, mac_data);
+ }
- /* DFT control: PHY bit: page769_20[0] = 1
- * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1
- */
- e1e_rphy(hw, I82579_DFT_CTRL, &phy_data);
- phy_data |= BIT(0);
- e1e_wphy(hw, I82579_DFT_CTRL, phy_data);
+ /* Disable the time synchronization clock */
+ mac_data = er32(FEXTNVM7);
+ mac_data |= BIT(31);
+ mac_data &= ~BIT(0);
+ ew32(FEXTNVM7, mac_data);
- mac_data = er32(EXTCNF_CTRL);
- mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG;
- ew32(EXTCNF_CTRL, mac_data);
+ /* Dynamic Power Gating Enable */
+ mac_data = er32(CTRL_EXT);
+ mac_data |= BIT(3);
+ ew32(CTRL_EXT, mac_data);
/* Check MAC Tx/Rx packet buffer pointers.
* Reset MAC Tx/Rx packet buffer pointers to suppress any
@@ -6416,59 +6478,6 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
mac_data = er32(RDFPC);
if (mac_data)
ew32(RDFPC, 0);
-
- /* Enable the Dynamic Power Gating in the MAC */
- mac_data = er32(FEXTNVM7);
- mac_data |= BIT(22);
- ew32(FEXTNVM7, mac_data);
-
- /* Disable the time synchronization clock */
- mac_data = er32(FEXTNVM7);
- mac_data |= BIT(31);
- mac_data &= ~BIT(0);
- ew32(FEXTNVM7, mac_data);
-
- /* Dynamic Power Gating Enable */
- mac_data = er32(CTRL_EXT);
- mac_data |= BIT(3);
- ew32(CTRL_EXT, mac_data);
-
- /* Disable disconnected cable conditioning for Power Gating */
- mac_data = er32(DPGFR);
- mac_data |= BIT(2);
- ew32(DPGFR, mac_data);
-
- /* Don't wake from dynamic Power Gating with clock request */
- mac_data = er32(FEXTNVM12);
- mac_data |= BIT(12);
- ew32(FEXTNVM12, mac_data);
-
- /* Ungate PGCB clock */
- mac_data = er32(FEXTNVM9);
- mac_data &= ~BIT(28);
- ew32(FEXTNVM9, mac_data);
-
- /* Enable K1 off to enable mPHY Power Gating */
- mac_data = er32(FEXTNVM6);
- mac_data |= BIT(31);
- ew32(FEXTNVM6, mac_data);
-
- /* Enable mPHY power gating for any link and speed */
- mac_data = er32(FEXTNVM8);
- mac_data |= BIT(9);
- ew32(FEXTNVM8, mac_data);
-
- /* Enable the Dynamic Clock Gating in the DMA and MAC */
- mac_data = er32(CTRL_EXT);
- mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN;
- ew32(CTRL_EXT, mac_data);
-
- /* No MAC DPG gating SLP_S0 in modern standby
- * Switch the logic of the lanphypc to use PMC counter
- */
- mac_data = er32(FEXTNVM5);
- mac_data |= BIT(7);
- ew32(FEXTNVM5, mac_data);
}
static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
@@ -6477,87 +6486,98 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
u32 mac_data;
u16 phy_data;
- /* Disable the Dynamic Power Gating in the MAC */
- mac_data = er32(FEXTNVM7);
- mac_data &= 0xFFBFFFFF;
- ew32(FEXTNVM7, mac_data);
+ if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) {
+ /* Request ME un configure the device from s0ix */
+ mac_data = er32(H2ME);
+ mac_data &= ~E1000_H2ME_START_DPG;
+ mac_data |= E1000_H2ME_EXIT_DPG;
+ ew32(H2ME, mac_data);
+ } else {
+ /* Request driver un configure the device from s0ix */
+
+ /* Disable the Dynamic Power Gating in the MAC */
+ mac_data = er32(FEXTNVM7);
+ mac_data &= 0xFFBFFFFF;
+ ew32(FEXTNVM7, mac_data);
+
+ /* Disable mPHY power gating for any link and speed */
+ mac_data = er32(FEXTNVM8);
+ mac_data &= ~BIT(9);
+ ew32(FEXTNVM8, mac_data);
+
+ /* Disable K1 off */
+ mac_data = er32(FEXTNVM6);
+ mac_data &= ~BIT(31);
+ ew32(FEXTNVM6, mac_data);
+
+ /* Disable Ungate PGCB clock */
+ mac_data = er32(FEXTNVM9);
+ mac_data |= BIT(28);
+ ew32(FEXTNVM9, mac_data);
+
+ /* Cancel not waking from dynamic
+ * Power Gating with clock request
+ */
+ mac_data = er32(FEXTNVM12);
+ mac_data &= ~BIT(12);
+ ew32(FEXTNVM12, mac_data);
- /* Enable the time synchronization clock */
- mac_data = er32(FEXTNVM7);
- mac_data |= BIT(0);
- ew32(FEXTNVM7, mac_data);
+ /* Cancel disable disconnected cable conditioning
+ * for Power Gating
+ */
+ mac_data = er32(DPGFR);
+ mac_data &= ~BIT(2);
+ ew32(DPGFR, mac_data);
- /* Disable mPHY power gating for any link and speed */
- mac_data = er32(FEXTNVM8);
- mac_data &= ~BIT(9);
- ew32(FEXTNVM8, mac_data);
+ /* Disable the Dynamic Clock Gating in the DMA and MAC */
+ mac_data = er32(CTRL_EXT);
+ mac_data &= 0xFFF7FFFF;
+ ew32(CTRL_EXT, mac_data);
- /* Disable K1 off */
- mac_data = er32(FEXTNVM6);
- mac_data &= ~BIT(31);
- ew32(FEXTNVM6, mac_data);
+ /* Revert the lanphypc logic to use the internal Gbe counter
+ * and not the PMC counter
+ */
+ mac_data = er32(FEXTNVM5);
+ mac_data &= 0xFFFFFF7F;
+ ew32(FEXTNVM5, mac_data);
- /* Disable Ungate PGCB clock */
- mac_data = er32(FEXTNVM9);
- mac_data |= BIT(28);
- ew32(FEXTNVM9, mac_data);
+ /* Enable the periodic inband message,
+ * Request PCIe clock in K1 page770_17[10:9] =01b
+ */
+ e1e_rphy(hw, HV_PM_CTRL, &phy_data);
+ phy_data &= 0xFBFF;
+ phy_data |= HV_PM_CTRL_K1_CLK_REQ;
+ e1e_wphy(hw, HV_PM_CTRL, phy_data);
- /* Cancel not waking from dynamic
- * Power Gating with clock request
- */
- mac_data = er32(FEXTNVM12);
- mac_data &= ~BIT(12);
- ew32(FEXTNVM12, mac_data);
+ /* Return back configuration
+ * 772_29[5] = 0 CS_Mode_Stay_In_K1
+ */
+ e1e_rphy(hw, I217_CGFREG, &phy_data);
+ phy_data &= 0xFFDF;
+ e1e_wphy(hw, I217_CGFREG, phy_data);
- /* Cancel disable disconnected cable conditioning
- * for Power Gating
- */
- mac_data = er32(DPGFR);
- mac_data &= ~BIT(2);
- ew32(DPGFR, mac_data);
+ /* Change the MAC/PHY interface to Kumeran
+ * Unforce the SMBus in PHY page769_23[0] = 0
+ * Unforce the SMBus in MAC CTRL_EXT[11] = 0
+ */
+ e1e_rphy(hw, CV_SMB_CTRL, &phy_data);
+ phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS;
+ e1e_wphy(hw, CV_SMB_CTRL, phy_data);
+ mac_data = er32(CTRL_EXT);
+ mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS;
+ ew32(CTRL_EXT, mac_data);
+ }
/* Disable Dynamic Power Gating */
mac_data = er32(CTRL_EXT);
mac_data &= 0xFFFFFFF7;
ew32(CTRL_EXT, mac_data);
- /* Disable the Dynamic Clock Gating in the DMA and MAC */
- mac_data = er32(CTRL_EXT);
- mac_data &= 0xFFF7FFFF;
- ew32(CTRL_EXT, mac_data);
-
- /* Revert the lanphypc logic to use the internal Gbe counter
- * and not the PMC counter
- */
- mac_data = er32(FEXTNVM5);
- mac_data &= 0xFFFFFF7F;
- ew32(FEXTNVM5, mac_data);
-
- /* Enable the periodic inband message,
- * Request PCIe clock in K1 page770_17[10:9] =01b
- */
- e1e_rphy(hw, HV_PM_CTRL, &phy_data);
- phy_data &= 0xFBFF;
- phy_data |= HV_PM_CTRL_K1_CLK_REQ;
- e1e_wphy(hw, HV_PM_CTRL, phy_data);
-
- /* Return back configuration
- * 772_29[5] = 0 CS_Mode_Stay_In_K1
- */
- e1e_rphy(hw, I217_CGFREG, &phy_data);
- phy_data &= 0xFFDF;
- e1e_wphy(hw, I217_CGFREG, phy_data);
-
- /* Change the MAC/PHY interface to Kumeran
- * Unforce the SMBus in PHY page769_23[0] = 0
- * Unforce the SMBus in MAC CTRL_EXT[11] = 0
- */
- e1e_rphy(hw, CV_SMB_CTRL, &phy_data);
- phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS;
- e1e_wphy(hw, CV_SMB_CTRL, phy_data);
- mac_data = er32(CTRL_EXT);
- mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS;
- ew32(CTRL_EXT, mac_data);
+ /* Enable the time synchronization clock */
+ mac_data = er32(FEXTNVM7);
+ mac_data &= ~BIT(31);
+ mac_data |= BIT(0);
+ ew32(FEXTNVM7, mac_data);
}
static int e1000e_pm_freeze(struct device *dev)
--
2.25.1
More information about the Intel-wired-lan
mailing list