[Intel-wired-lan] [PATCH net] ice: Fix broken IFF_ALLMULTI handling
Marcin Szycik
marcin.szycik at linux.intel.com
Wed Mar 23 20:05:20 UTC 2022
On 21-Mar-22 20:17, Ivan Vecera wrote:
> Handling of all-multicast flag and associated multicast promiscuous
> mode is broken in ice driver. When a user switches allmulticast
> flag on or off the driver checks whether any VLANs are configured
> over the interface (except default VLAN 0).
>
> If any extra VLANs are registered it enables multicast promiscuous
> mode for all these VLANs (including default VLAN 0) using
> ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all
> multicast packets tagged with known VLAN ID or untagged are received
> and multicast packets tagged with unknown VLAN ID ignored.
>
> If no extra VLANs are registered (so only VLAN 0 exists) it enables
> multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC
> look-up type. In this situation any multicast packets including
> tagged ones are received.
>
> The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:
>
> ice_vsi_sync_fltr() {
> ...
> if (changed_flags & IFF_ALLMULTI) {
> if (netdev->flags & IFF_ALLMULTI) {
> if (vsi->num_vlans > 1)
> ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
> else
> ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
> } else {
> if (vsi->num_vlans > 1)
> ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
> else
> ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
> }
> }
> ...
> }
>
> The code above depends on value vsi->num_vlan that specifies number
> of VLANs configured over the interface (including VLAN 0) and
> this is problem because that value is modified in NDO callbacks
> ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().
>
> Scenario 1:
> 1. ip link set ens7f0 allmulticast on
> 2. ip link add vlan10 link ens7f0 type vlan id 10
> 3. ip link set ens7f0 allmulticast off
> 4. ip link set ens7f0 allmulticast on
>
> [1] In this scenario IFF_ALLMULTI is enabled and the driver calls
> ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs
> multicast promisc rule with non-VLAN look-up type.
> [2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
> [3] Command switches IFF_ALLMULTI off and the driver calls
> ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this
> call is effectively NOP because it looks for multicast promisc
> rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such
> rules exist. So the all-multicast remains enabled silently
> in hardware.
> [4] Command tries to switch IFF_ALLMULTI on and the driver calls
> ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call
> fails (-EEXIST) because non-VLAN multicast promisc rule already
> exists.
>
> Scenario 2:
> 1. ip link add vlan10 link ens7f0 type vlan id 10
> 2. ip link set ens7f0 allmulticast on
> 3. ip link add vlan20 link ens7f0 type vlan id 20
> 4. ip link del vlan10 ; ip link del vlan20
> 5. ip link set ens7f0 allmulticast off
>
> [1] VLAN with ID 10 is added and vsi->num_vlan==2
> [2] Command switches IFF_ALLMULTI on and driver installs multicast
> promisc rules with VLAN look-up type for VLAN 0 and 10
> [3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast
> promisc rules is added for this new VLAN so the interface does
> not receive MC packets from VLAN 20
> [4] Both VLANs are removed but multicast rule for VLAN 10 remains
> installed so interface receives multicast packets from VLAN 10
> [5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1
> the driver tries to remove multicast promisc rule for VLAN 0
> with non-VLAN look-up that does not exist.
> All-multicast looks disabled from user point of view but it
> is partially enabled in HW (interface receives all multicast
> packets either untagged or tagged with VLAN ID 10)
>
> To resolve these issues the patch introduces these changes:
> 1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and
> ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed
> and IFF_ALLMULTI is enabled an appropriate multicast promisc
> rule for that VLAN ID is added/removed.
> 2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added
> so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up
> type for existing multicast promisc rule for VLAN 0 is updated
> to ICE_MCAST_VLAN_PROMISC_BITS.
> 3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed
> so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up
> type for existing multicast promisc rule for VLAN 0 is updated
> to ICE_MCAST_PROMISC_BITS.
> 4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY
> bit protection to avoid races with ice_vsi_sync_fltr() that runs
> in ice_service_task() context.
> 5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
> 6. Error messages added to ice_fltr_*_vsi_promisc() helper functions
> to avoid them in their callers
> 7. Small improvements to increase readability
>
> Fixes: 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
> Signed-off-by: Ivan Vecera <ivecera at redhat.com>
> ---
> drivers/net/ethernet/intel/ice/ice.h | 1 -
> drivers/net/ethernet/intel/ice/ice_fltr.c | 52 +++++++++-
> drivers/net/ethernet/intel/ice/ice_main.c | 119 +++++++++++++++-------
> 3 files changed, 131 insertions(+), 41 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ice/ice.h b/drivers/net/ethernet/intel/ice/ice.h
> index bea1d1e39fa2..717542e49d65 100644
> --- a/drivers/net/ethernet/intel/ice/ice.h
> +++ b/drivers/net/ethernet/intel/ice/ice.h
> @@ -300,7 +300,6 @@ enum ice_vsi_state {
> ICE_VSI_NETDEV_REGISTERED,
> ICE_VSI_UMAC_FLTR_CHANGED,
> ICE_VSI_MMAC_FLTR_CHANGED,
> - ICE_VSI_VLAN_FLTR_CHANGED,
> ICE_VSI_PROMISC_CHANGED,
> ICE_VSI_STATE_NBITS /* must be last */
> };
> diff --git a/drivers/net/ethernet/intel/ice/ice_fltr.c b/drivers/net/ethernet/intel/ice/ice_fltr.c
> index c29177c6bb9d..8ed87b43a367 100644
> --- a/drivers/net/ethernet/intel/ice/ice_fltr.c
> +++ b/drivers/net/ethernet/intel/ice/ice_fltr.c
> @@ -58,7 +58,18 @@ int
> ice_fltr_set_vlan_vsi_promisc(struct ice_hw *hw, struct ice_vsi *vsi,
> u8 promisc_mask)
> {
> - return ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, false);
> + struct ice_pf *pf = hw->back;
> + int result;
> +
> + result = ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, false);
> + if (!result)
> + return result;
> +
> + dev_err(ice_pf_to_dev(pf),
> + "Error setting promisc mode on VSI %i (rc=%d)\n", vsi->vsi_num,
> + result);
> +
> + return result;
> }
>
> /**
> @@ -73,7 +84,18 @@ int
> ice_fltr_clear_vlan_vsi_promisc(struct ice_hw *hw, struct ice_vsi *vsi,
> u8 promisc_mask)
> {
> - return ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, true);
> + struct ice_pf *pf = hw->back;
> + int result;
> +
> + result = ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, true);
> + if (!result)
> + return result;
> +
> + dev_err(ice_pf_to_dev(pf),
> + "Error clearing promisc mode on VSI %i (rc=%d)\n",
> + vsi->vsi_num, result);
> +
> + return result;
> }
>
> /**
> @@ -87,7 +109,18 @@ int
> ice_fltr_clear_vsi_promisc(struct ice_hw *hw, u16 vsi_handle, u8 promisc_mask,
> u16 vid)
> {
> - return ice_clear_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
> + struct ice_pf *pf = hw->back;
> + int result;
> +
> + result = ice_clear_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
> + if (!result)
> + return result;
> +
> + dev_err(ice_pf_to_dev(pf),
> + "Error clearing promisc mode on VSI %i for VID %u (rc=%d)\n",
> + ice_get_hw_vsi_num(hw, vsi_handle), vid, result);
> +
> + return result;
> }
>
> /**
> @@ -101,7 +134,18 @@ int
> ice_fltr_set_vsi_promisc(struct ice_hw *hw, u16 vsi_handle, u8 promisc_mask,
> u16 vid)
> {
> - return ice_set_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
> + struct ice_pf *pf = hw->back;
> + int result;
> +
> + result = ice_set_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
> + if (!result)
> + return result;
> +
> + dev_err(ice_pf_to_dev(pf),
> + "Error setting promisc mode on VSI %i for VID %u (rc=%d)\n",
> + ice_get_hw_vsi_num(hw, vsi_handle), vid, result);
> +
> + return result;
> }
>
> /**
> diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
> index b7e8744b0c0a..168a41ea37b8 100644
> --- a/drivers/net/ethernet/intel/ice/ice_main.c
> +++ b/drivers/net/ethernet/intel/ice/ice_main.c
> @@ -227,8 +227,7 @@ static int ice_add_mac_to_unsync_list(struct net_device *netdev, const u8 *addr)
> static bool ice_vsi_fltr_changed(struct ice_vsi *vsi)
> {
> return test_bit(ICE_VSI_UMAC_FLTR_CHANGED, vsi->state) ||
> - test_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state) ||
> - test_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
> + test_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state);
> }
>
> /**
> @@ -244,10 +243,15 @@ static int ice_set_promisc(struct ice_vsi *vsi, u8 promisc_m)
> if (vsi->type != ICE_VSI_PF)
> return 0;
>
> - if (vsi->num_vlan > 1)
> - status = ice_fltr_set_vlan_vsi_promisc(&vsi->back->hw, vsi, promisc_m);
> - else
> - status = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx, promisc_m, 0);
> + if (vsi->num_vlan > 1) {
> + promisc_m |= (ICE_PROMISC_VLAN_RX | ICE_PROMISC_VLAN_TX);
> + status = ice_fltr_set_vlan_vsi_promisc(&vsi->back->hw, vsi,
> + promisc_m);
> + } else {
> + status = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
> + promisc_m, 0);
> + }
> +
> return status;
> }
>
> @@ -264,10 +268,15 @@ static int ice_clear_promisc(struct ice_vsi *vsi, u8 promisc_m)
> if (vsi->type != ICE_VSI_PF)
> return 0;
>
> - if (vsi->num_vlan > 1)
> - status = ice_fltr_clear_vlan_vsi_promisc(&vsi->back->hw, vsi, promisc_m);
> - else
> - status = ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx, promisc_m, 0);
> + if (vsi->num_vlan > 1) {
> + promisc_m |= (ICE_PROMISC_VLAN_RX | ICE_PROMISC_VLAN_TX);
> + status = ice_fltr_clear_vlan_vsi_promisc(&vsi->back->hw, vsi,
> + promisc_m);
> + } else {
> + status = ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
> + promisc_m, 0);
> + }
> +
> return status;
> }
>
> @@ -285,7 +294,6 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
> struct ice_pf *pf = vsi->back;
> struct ice_hw *hw = &pf->hw;
> u32 changed_flags = 0;
> - u8 promisc_m;
> int err;
>
> if (!vsi->netdev)
> @@ -303,7 +311,6 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
> if (ice_vsi_fltr_changed(vsi)) {
> clear_bit(ICE_VSI_UMAC_FLTR_CHANGED, vsi->state);
> clear_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state);
> - clear_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
>
> /* grab the netdev's addr_list_lock */
> netif_addr_lock_bh(netdev);
> @@ -352,29 +359,15 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
> /* check for changes in promiscuous modes */
> if (changed_flags & IFF_ALLMULTI) {
> if (vsi->current_netdev_flags & IFF_ALLMULTI) {
> - if (vsi->num_vlan > 1)
> - promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
> - else
> - promisc_m = ICE_MCAST_PROMISC_BITS;
Because `ice_{set,clear}_promisc()` are now always called with the same second argument (ICE_MCAST_PROMISC_BITS), wouldn't it be better to remove the arg and instead call `ice_fltr_{clear,set}_{vlan,vsi}_vsi_promisc()` with either ICE_MCAST_VLAN_PROMISC_BITS or ICE_MCAST_PROMISC_BITS inside the function?
> -
> - err = ice_set_promisc(vsi, promisc_m);
> + err = ice_set_promisc(vsi, ICE_MCAST_PROMISC_BITS);> if (err) {
> - netdev_err(netdev, "Error setting Multicast promiscuous mode on VSI %i\n",
> - vsi->vsi_num);
> vsi->current_netdev_flags &= ~IFF_ALLMULTI;
> goto out_promisc;
> }
> } else {
> /* !(vsi->current_netdev_flags & IFF_ALLMULTI) */
> - if (vsi->num_vlan > 1)
> - promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
> - else
> - promisc_m = ICE_MCAST_PROMISC_BITS;
> -
> - err = ice_clear_promisc(vsi, promisc_m);
> + err = ice_clear_promisc(vsi, ICE_MCAST_PROMISC_BITS);
> if (err) {
> - netdev_err(netdev, "Error clearing Multicast promiscuous mode on VSI %i\n",
> - vsi->vsi_num);
> vsi->current_netdev_flags |= IFF_ALLMULTI;
> goto out_promisc;
> }
> @@ -3445,19 +3438,47 @@ ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto,
> if (!vid)
> return 0;
>
> + while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
> + usleep_range(1000, 2000);
> +
> /* Enable VLAN pruning when a VLAN other than 0 is added */
> if (!ice_vsi_is_vlan_pruning_ena(vsi)) {
> ret = ice_cfg_vlan_pruning(vsi, true);
> if (ret)
> - return ret;
> + goto finish;
> + }
> +
> + /* Add multicast promisc rule for the VLAN ID to be added if
> + * all-multicast is currently enabled.
> + */
> + if (vsi->current_netdev_flags & IFF_ALLMULTI) {
> + ret = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
> + ICE_MCAST_VLAN_PROMISC_BITS,
> + vid);
> + if (ret)
> + goto finish;
> }
>
> /* Add a switch rule for this VLAN ID so its corresponding VLAN tagged
> * packets aren't pruned by the device's internal switch on Rx
> */
> ret = ice_vsi_add_vlan(vsi, vid, ICE_FWD_TO_VSI);
> - if (!ret)
> - set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
> + if (ret)
> + goto finish;
> +
> + /* If all-multicast is currently enabled and this VLAN ID is only one
> + * besides VLAN-0 we have to update look-up type of multicast promisc
> + * rule for VLAN-0 from ICE_SW_LKUP_PROMISC to ICE_SW_LKUP_PROMISC_VLAN.
> + */
> + if ((vsi->current_netdev_flags & IFF_ALLMULTI) && vsi->num_vlan == 2) {
> + ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
> + ICE_MCAST_PROMISC_BITS, 0);
> + ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
> + ICE_MCAST_VLAN_PROMISC_BITS, 0);
> + }
> +
> +finish:
> + clear_bit(ICE_CFG_BUSY, vsi->state);
>
> return ret;
> }
> @@ -3482,18 +3503,44 @@ ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto,
> if (!vid)
> return 0;
>
> + while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
> + usleep_range(1000, 2000);
> +
> /* Make sure ice_vsi_kill_vlan is successful before updating VLAN
> * information
> */
> ret = ice_vsi_kill_vlan(vsi, vid);
> if (ret)
> - return ret;
> + goto finish;
>
> - /* Disable pruning when VLAN 0 is the only VLAN rule */
> - if (vsi->num_vlan == 1 && ice_vsi_is_vlan_pruning_ena(vsi))
> - ret = ice_cfg_vlan_pruning(vsi, false);
> + /* Remove multicast promisc rule for the removed VLAN ID if
> + * all-multicast is enabled.
> + */
> + if (vsi->current_netdev_flags & IFF_ALLMULTI)
> + ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
> + ICE_MCAST_VLAN_PROMISC_BITS, vid);
> +
> + if (vsi->num_vlan == 1) {
> + /* Disable pruning when VLAN 0 is the only VLAN rule */
> + if (ice_vsi_is_vlan_pruning_ena(vsi))
> + ice_cfg_vlan_pruning(vsi, false);
Why was `ret = ...` removed here?
> +
> + /* Update look-up type of multicast promisc rule for VLAN 0
> + * from ICE_SW_LKUP_PROMISC_VLAN to ICE_SW_LKUP_PROMISC when
> + * all-multicast is enabled and VLAN 0 is the only VLAN rule.
> + */
> + if (vsi->current_netdev_flags & IFF_ALLMULTI) {
> + ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
> + ICE_MCAST_VLAN_PROMISC_BITS,
> + 0);
> + ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
> + ICE_MCAST_PROMISC_BITS, 0);
> + }
> + }
> +
> +finish:
> + clear_bit(ICE_CFG_BUSY, vsi->state);
>
> - set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
> return ret;
> }
>
Otherwise LGTM (though my experience in this area is rather limited).
Marcin
More information about the Intel-wired-lan
mailing list