[Intel-wired-lan] [PATCH iwl-next] ixgbe: Add 1000BASE-BX support
Ernesto Castellotti
ernesto at castellotti.net
Sat Jan 27 17:48:00 UTC 2024
Added support for 1000BASE-BX, i.e. Gigabit Ethernet over single strand
of single-mode fiber).
The initialization of a 1000BASE-BX SFP is the same as 1000BASE-SX/LX
with the only difference that the Bit Rate Nominal Value must be
checked to make sure it is a Gigabit Ethernet transceiver, as described
by the SFF-8472 specification.
This was tested with the FS.com SFP-GE-BX 1310/1490nm 10km transceiver:
$ ethtool -m eth4
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x40 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: BASE-BX10
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 10km
Length (SMF) : 10000m
Length (50um) : 0m
Length (62.5um) : 0m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 1310nm
Vendor name : FS
Vendor OUI : 64:9d:99
Vendor PN : SFP-GE-BX
Vendor rev :
Option values : 0x20 0x0a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : Power level 3 requirement
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : S2202359108
Date code : 220307
Optical diagnostics support : Yes
Laser bias current : 17.650 mA
Laser output power : 0.2132 mW / -6.71 dBm
Receiver signal average optical power : 0.2740 mW / -5.62 dBm
Module temperature : 47.30 degrees C / 117.13 degrees F
Module voltage : 3.2576 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 110.000 mA
Laser bias current low alarm threshold : 1.000 mA
Laser bias current high warning threshold : 100.000 mA
Laser bias current low warning threshold : 1.000 mA
Laser output power high alarm threshold : 0.7079 mW / -1.50 dBm
Laser output power low alarm threshold : 0.0891 mW / -10.50 dBm
Laser output power high warning threshold : 0.6310 mW / -2.00 dBm
Laser output power low warning threshold : 0.1000 mW / -10.00 dBm
Module temperature high alarm threshold : 90.00 degrees C / 194.00 degrees F
Module temperature low alarm threshold : -45.00 degrees C / -49.00 degrees F
Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
Module temperature low warning threshold : -40.00 degrees C / -40.00 degrees F
Module voltage high alarm threshold : 3.7950 V
Module voltage low alarm threshold : 2.8050 V
Module voltage high warning threshold : 3.4650 V
Module voltage low warning threshold : 3.1350 V
Laser rx power high alarm threshold : 0.7079 mW / -1.50 dBm
Laser rx power low alarm threshold : 0.0028 mW / -25.53 dBm
Laser rx power high warning threshold : 0.6310 mW / -2.00 dBm
Laser rx power low warning threshold : 0.0032 mW / -24.95 dBm
Signed-off-by: Ernesto Castellotti <ernesto at castellotti.net>
---
.../net/ethernet/intel/ixgbe/ixgbe_82599.c | 4 ++-
.../net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 2 ++
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 33 ++++++++++++++++---
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h | 2 ++
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 3 ++
5 files changed, 39 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
index 339e106a5732..7943e8c59f2f 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
@@ -334,7 +334,9 @@ static s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw,
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
- hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) {
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_bx_core0 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_bx_core1) {
*speed = IXGBE_LINK_SPEED_1GB_FULL;
*autoneg = true;
return 0;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index 9a63457712c7..4387beeda1ad 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -349,6 +349,8 @@ static int ixgbe_get_link_ksettings(struct net_device *netdev,
case ixgbe_sfp_type_1g_sx_core1:
case ixgbe_sfp_type_1g_lx_core0:
case ixgbe_sfp_type_1g_lx_core1:
+ case ixgbe_sfp_type_1g_bx_core0:
+ case ixgbe_sfp_type_1g_bx_core1:
ethtool_link_ksettings_add_link_mode(cmd, supported,
FIBRE);
ethtool_link_ksettings_add_link_mode(cmd, advertising,
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index f28140a05f09..3163263e3b53 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -1539,6 +1539,7 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
u8 oui_bytes[3] = {0, 0, 0};
u8 cable_tech = 0;
u8 cable_spec = 0;
+ u8 bitrate_nominal = 0;
u16 enforce_sfp = 0;
if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber) {
@@ -1577,6 +1578,13 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
IXGBE_SFF_CABLE_TECHNOLOGY,
&cable_tech);
+ if (status)
+ goto err_read_i2c_eeprom;
+
+ status = hw->phy.ops.read_i2c_eeprom(hw,
+ IXGBE_SFF_BITRATE_NOMINAL,
+ &bitrate_nominal);
+
if (status)
goto err_read_i2c_eeprom;
@@ -1659,6 +1667,17 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
else
hw->phy.sfp_type =
ixgbe_sfp_type_1g_lx_core1;
+ // Support only 1000BASE-BX10, checking the Bit Rate Nominal Value as per SFF-8472
+ // by convention 1.25 Gb/s should be rounded up to 0Dh (13 in units of 100 MBd)
+ // for Ethernet 1000BASE-X
+ } else if ((comp_codes_1g & IXGBE_SFF_BASEBX10_CAPABLE) &&
+ (bitrate_nominal == 0xD)) {
+ if (hw->bus.lan_id == 0)
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_1g_bx_core0;
+ else
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_1g_bx_core1;
} else {
hw->phy.sfp_type = ixgbe_sfp_type_unknown;
}
@@ -1747,7 +1766,9 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
- hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1)) {
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_bx_core0 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_bx_core1)) {
hw->phy.type = ixgbe_phy_sfp_unsupported;
return -EOPNOTSUPP;
}
@@ -1763,7 +1784,9 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
- hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1)) {
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_bx_core0 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_bx_core1)) {
/* Make sure we're a supported PHY type */
if (hw->phy.type == ixgbe_phy_sfp_intel)
return 0;
@@ -1999,12 +2022,14 @@ s32 ixgbe_get_sfp_init_sequence_offsets(struct ixgbe_hw *hw,
if (sfp_type == ixgbe_sfp_type_da_act_lmt_core0 ||
sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
sfp_type == ixgbe_sfp_type_1g_cu_core0 ||
- sfp_type == ixgbe_sfp_type_1g_sx_core0)
+ sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
+ sfp_type == ixgbe_sfp_type_1g_bx_core0)
sfp_type = ixgbe_sfp_type_srlr_core0;
else if (sfp_type == ixgbe_sfp_type_da_act_lmt_core1 ||
sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
sfp_type == ixgbe_sfp_type_1g_cu_core1 ||
- sfp_type == ixgbe_sfp_type_1g_sx_core1)
+ sfp_type == ixgbe_sfp_type_1g_sx_core1 ||
+ sfp_type == ixgbe_sfp_type_1g_bx_core1)
sfp_type = ixgbe_sfp_type_srlr_core1;
/* Read offset to PHY init contents */
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
index ef72729d7c93..b5bc60916402 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
@@ -17,6 +17,7 @@
#define IXGBE_SFF_1GBE_COMP_CODES 0x6
#define IXGBE_SFF_10GBE_COMP_CODES 0x3
#define IXGBE_SFF_CABLE_TECHNOLOGY 0x8
+#define IXGBE_SFF_BITRATE_NOMINAL 0xC
#define IXGBE_SFF_CABLE_SPEC_COMP 0x3C
#define IXGBE_SFF_SFF_8472_SWAP 0x5C
#define IXGBE_SFF_SFF_8472_COMP 0x5E
@@ -39,6 +40,7 @@
#define IXGBE_SFF_1GBASESX_CAPABLE 0x1
#define IXGBE_SFF_1GBASELX_CAPABLE 0x2
#define IXGBE_SFF_1GBASET_CAPABLE 0x8
+#define IXGBE_SFF_BASEBX10_CAPABLE 0x64
#define IXGBE_SFF_10GBASESR_CAPABLE 0x10
#define IXGBE_SFF_10GBASELR_CAPABLE 0x20
#define IXGBE_SFF_SOFT_RS_SELECT_MASK 0x8
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index 61b9774b3d31..f111a671ee82 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -3210,6 +3210,9 @@ enum ixgbe_sfp_type {
ixgbe_sfp_type_1g_sx_core1 = 12,
ixgbe_sfp_type_1g_lx_core0 = 13,
ixgbe_sfp_type_1g_lx_core1 = 14,
+ ixgbe_sfp_type_1g_bx_core0 = 15,
+ ixgbe_sfp_type_1g_bx_core1 = 16,
+
ixgbe_sfp_type_not_present = 0xFFFE,
ixgbe_sfp_type_unknown = 0xFFFF
};
--
2.43.0
More information about the Intel-wired-lan
mailing list